Samsung Washer Parts

Find your part

Enter your model number or a part number and click "Search"

Here is an example model number plate:

tag sample

Samsung Appliance Parts

Popular Samsung Washer Parts

Drain Pump Assembly - 120V 60Hz

PartSelect Number PS4204638

Manufacturer Part Number DC31-00054A

This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintained for a specific period of time during the spin cycle. You may need to replace the pump assembly if your washer is not draining properly; it could be clogged or damaged. Be sure to disconnect the water supply and power to your appliance before repairing. This part is located at the rear of the washer behind the back panel.

Door Lock Latch

PartSelect Number PS11745016

Manufacturer Part Number WP8182634

This part is used on front load washers and includes the interlock switch assembly.

Fixes these symptoms

  • Door latch failure
  • Lid or door will not open
  • Lid or door won't close
  • See more...

Installation Instructions

James from Vilonia, AR

front load washer latch replacement

1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish. Read more...

Hex Head Bolt – Part Number: DC60-40137A

Hex Head Bolt

PartSelect Number PS4205366

Manufacturer Part Number DC60-40137A

This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bolts. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.

Installation Instructions

Samuel from NEEDVILLE, TX

Washer making noise a snow smoking.

Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in. Read more...

VALVE-WATER;V-0117,NYLON

PartSelect Number PS4209100

Manufacturer Part Number DC62-30314K

One solenoid valve for hot water

Door Switch Assembly – Part Number: DC64-00519B

Door Switch Assembly

PartSelect Number PS4210737

Manufacturer Part Number DC64-00519B

Fixes these symptoms

  • Lid or door won't close
  • See more...

Installation Instructions

Arthur from WILLARD, OH

The washing would stop in mid cycle and the door would be locked.

An initial issue was getting the door to unlock. I tired several things but finally was able to pull the door as if to open it and put something between the door handle and the front of the washer while I ran a washer cycle. There is a way to take the washer top off and reach down inside the unit and pull down on a release, but I did not try that.

The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.

Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.

Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.

The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.

Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.

Attach the new switch to the sets of wires.

Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.

Slide the switch through the opening where you removed it. and re-attach it using the two screws.

Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.

By the way, The service was great and exceeded by expectations.

Read more...

Inlet Hose - 5 FT – Part Number: WP89503

Inlet Hose - 5 FT

PartSelect Number PS11746820

Manufacturer Part Number WP89503

This hose can handle hot or cold water and is five feet long.

Installation Instructions

Helen from NASHUA, NH

Leaking water inlet hoses.

Removed the old hoses and screwed on the new hoses. Read more...

PULSATOR-CAP – Part Number: DC66-00777A

PULSATOR-CAP

PartSelect Number PS8753312

Manufacturer Part Number DC66-00777A

Installation Instructions

James from GALLATIN, TN

The cap came off somehow

Just snapped on part in the center of tub where it belongs Read more...

Water Temperature Thermistor – Part Number: DC90-10128N

Water Temperature Thermistor

PartSelect Number PS4214274

Manufacturer Part Number DC90-10128N

The thermistor monitors and helps regulator the water temperature in the washer.

Hose Clamp

PartSelect Number PS11743008

Manufacturer Part Number WP596669

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

Fixes these symptoms

  • Leaking
  • Will not stop filling with water
  • See more...

Installation Instructions

jeff from lindenhurst, IL

Washing Machine was leaking water

Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...

Washer Water-Level Pressure Switch – Part Number: DC96-01703B

Appliance Type

  • Washer Parts
  • Samsung Parts

Popular Samsung Washer Models

Below are the most popular Samsung Washer models we have. Enter your model number in the search box to find your model.

  • WF42H5000AW WASHER
  • WF42H5000AW WASHER
  • WA48H7400AW WASHER
  • WA48H7400AW RESIDENTIAL
  • WA48H7400AW WASHER
  • WA48H7400AW WASHER
  • WA45H7000AW WASHER
  • WA45H7000AW WASHER
  • WA45H7000AW WASHER
  • WA45H7000AW WASHER
  • WA45H7000AW WASHER
  • WF42H5200AW WASHER
  • WF42H5200AW WASHER
  • WF45K6500AV WASHER
  • WA50F9A6DSW WASHER
  • WA50F9A6DSW WASHER
  • WF42H5200AP WASHER
  • WF42H5200AP WASHER
  • WA400PJHDWR WASHER
  • WA400PJHDWR WASHER